Feature(may vary by option.)
●This Wifi Outdoor Bridge works at 2.4Ghz band, built-in 8dbi antenna, Max 300Mbps between the bridge, support 1KM long-distance wireless transmission, automatically adjust the transmission power and channel, reduce signal interference, make wireless transmission more stable
●The installation is very simple. It is powered by a 24V poe adapter(included) and supports dial pairing. Set one of the CPE DIP switches to H, set it host and transmit the signal; and set the other CPE switch to C, set it slave client and receive the signal; then reset, will automatically complete pairing, no other configuration required. There are two 100Mpbs Ethernet ports, the WAN port connect to the POE Adapter POE Port, the LAN port connect to the LAN device.
●Full information LED display, include host-client mode(H or C,the number behind is the channel number), signal strength(P,a number will be displayed after the pairing is successful), IP address(A), port /wifi/power led, the F button can switch the LED display info, the S button can complete the setting, more clearly know the device status, more conducive to debugging and maintenance
●Built-in independent hardware protection circuit and watchdog chip, when working abnormally, it will automatically restart to maintain the continuity of wireless coverage; support WEB GUI management, view operating status, support wifi analysis and configuration
●Professional outdoor shell design, seamless molding, IP65 dustproof and waterproof, lightning protection, support PtP, PtMP(1-4); Also support one single independent use, both set at the Host mode, with complete AP function, used for wifi access, maximum support 50+ users. It can be widely used indoor and outdoor, for home, enterprise network, wireless coverage, security monitoring transmission, great for expanding your network wirelessly.
[2.4G 1KM]
[5.8G 2-3KM]
Description
FAQs:
Q:Does the lan port supply POE power to the connected device?
A: Only WAN port support POE(LAN port not support),If you are going to connect more than one device - use a POE switch.
Q: What are the dimensions of the device?
A: It is in the product information section: 6.61x3.46x2.26 inches.
Q: How can I mount them?
A: You can fix it on the wall and pillar with a cable tie or screws.
Q: Does it work automatically after power outage is restored? Does it need re-pairing or re- setup?
A: It will restore automatically after power outages,no intervention required.
Q: How many points can I connect together to send a lan signal?
A: Recommend 4, you can try more.
Q: Are the ethernet ports on these devices 10/100/1000 Mbps?
A: The CPE ethernet ports for WB300/WB900 are 100Mbps, but the wireless transmission speed between 2 bridges max is 900Mbps(WB900)/300Mbps(WB300).
Q: How to connect the bridges wifi?
A: The default wifi password of the main bridge is 66666666, the wifi of the slave bridge is closed by default, and the wifi status and password can be modified in the web management interface
|
|
|
|
|---|---|---|
300Mbps Data Rate & Dual Ethernet PortsWB300 wireless outdoor bridge features 802.11ac Wi-Fi and 2*2 MIMO technology, 300Mbps wireless speed. Equipped with dual ethernet port ensures high speed internet access and more end users access. |
Long Range Wi-Fi TransmissionWB300 wireless outdoor bridge with 8dBi high gain antenna, the Wi-Fi range is more than 1000 meters, it is the device with very stable performance in long range, but competitive in cost. |
One Key BridgeWB300 wireless outdoor cpe with one-key bridge configure steps, simple to complete the entire system configuration, supply more efficient service for your networking. |
|
|
|
|
|---|---|---|
IP65 Weatherproof and Lighting ProtectionWith an outdoor waterproof and dustproof enclosure,buidling in lighting protection IC, this bridge can be used in various weather conditions for stable performance. |
LED DisplayWith LED signal lights to show master/slave,address and signal strength, easy to find a suitable place of outdoor CPE. |
24V PoE PowerMokerLink wireless bridge has integrated 24V passive Power over Ethernet (PoE), for easy installation and lower cost. So it can be installed in areas where power outlets are not readily available, eliminating the mess of altering existing network infrastructure. |
|
|
|
|
|---|---|---|
AP+Repeater Operation ModeWB300 wireless outdoor bridge support gateway, wireless AP, WiFi repeater operation mode, it is widely used in WiFi bridge connection and wireless security; |
Watchdog FunctionWhen the wireless bridge communication fails, the corresponding CPE will automatically detect and restart, restore network communication by itself, and reduce manual intervention and maintenance. |
Adjustable Radio Transmit PowerAccording to the usage scenarios,adjust radio transmit power.Improve the stability of wireless system,reduce signal interference between CPEs. |
Connection Topology
In the wireless monitoring transmission,it is recommended to use the above graphic method for point-to-point or point-to-multi-point transmission.The wireless bridge/outdoor CPE transmission angle is oriented at 60 degrees.Please adjust the equipments angle when building point-to-multi-point transmission.
You can use master cpe as wirless access point if you enable SSID on web page of this cpe.
Two bridge ways:One Key Bridge & LED Display Bridge,Choose the way based on request.
1.One Key Bridge
1.1 Config Master/Slave CPE - Put the switch to H,CPE will work as Master,Put the switch to C,CPE will work as Slave.
1.2 Point to Point Connection - Press reset button on both master and slave CPE,will start bridging.
Point to mult Point connection - Press reset button on master and mult salve CPEs,will start bridging.
Note:Master CPE and Slave CPE bridging actions(reset button) need to be finished in 1 minute.
2.LED Display Bridge
2.1 Config Master/Slave CPE - When bridge two CPEs,make one work as master:Press F to make H/C blinking,and press S to change to H,make the other work as slave:Press F to make H/C blinking,and press S to change to C,it will save automatically in 5 seconds.
2.2 Point to Point Connection - Press reset button on both master and slave CPE,will start bridging.
Point to mult Point connection - Press reset button on master and mult salve CPEs,will start bridging.
Note:Master CPE and Slave CPE bridging actions(reset button) need to be finished in 1 minute.