Feature

●Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 55mm (2 3/16”) behind the panel to fit the gauge. Put the gauge in the hole and screw down.
●GPS Blind Area Odometer Compensation, Speed ≠0 and show accurate speed in tunnel with the help of accelerometer, No Stationary Drift
●9-32V Working Voltage, Amber backlight available, High Beam, Neutral, Alarm, Oil Pressure Alarm, Left Turn, Right Turn, BSD(Need buy additional Blind Spot Alarm with BSD Sensor )
●Securely fasten GPS antenna, preferably outdoors (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. Do not cut cable
●OverSpeed Buzzer Alarm, Total Mileage Adjustable, Reverse polarity protection and anti-fogging performance Mileage Range: 0-999999 (KM, Mi, NMI)

Description

Product Features:

-Electronic Speedometer with Unique High Definition and Contrast Ratio LCD

-No Mechanical Sensor, get speed signal from GPS, No GPS Stationary Drift

-Total Mileage Adjustable, Trip Odometer Reset

-GPS Blind Area Odometer Compensation

-Switch unit between MPH(Mi), Knots(NMI) and Km/h (KM)

-Tachometer Speed Ratio Programmable

-OverSpeed Buzzer Alarm (Value Adjustable)

-Reverse polarity protection and anti-fogging performance

Product Introduction


How to install it? - Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 55mm (2 3/16”) behind the panel to fit the gauge. - Put the gauge in the hole and tighten. - For the GPS antenna, you should securely fasten it in the flat position, black side upwards, preferably outside (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. And do not cut cable.	GPS speedometer keeps counting? After installation in the first time, GPS speedometer needs to search for signal, thats the reason that LCD counts numbers all the time. After getting signal, LCD will come back to 0. It is normal.	Why Dont get RPM signal? Tachometer sometimes cannot get signal by ignition system. So, I suggest Tacho sensor signal. It is more stable. I suggest you can buy a Tacho sensor from Eling Parts. NO. is B07RR8NQ45, B07RN3HJ72.

Technical Data

Fixing dimension	85mm(3-3/8")
Tachometer Indicating Range	0-19999RPM
SOG Indicating Range	0-299(Km/h, MPH, Knots)
TRIP Indicating Range	0-999.9 (KM, Mi, NMI )
ODO Indicating Range	0-999999 (KM, Mi, NMI )
Indicator	High Beam, Neutral, Alarm, Oil Pressure Alarm, Left Turn, Right Turn, BSD(Need buy additional Blind Spot Alarm with BSD Sensor )
Working Voltage	12V/24V (If installed on E-bike, which has max 80V DC, power adapter will be needed)
OverSpeed Alarm	OverSpeed Buzzer Alarm (Value Adjustable)
Protection Grade	IP67
Working temperatures	- 40 to 85°C
Operation mode	LCD display, stepper motor

How to be setting Tach RPM Ratio?

1. Press the button for 2-3 seconds first, then turn on the power supply.

2. Release the button after seeing “PULSE”; Press the button to set up speed ratio from 0.5 to 327. After adjustment, release button and wait for menu to complete flashing.

3. After setting, release button and wait for menu to complete flashing., then it will save the setting.

4. Please note: If your sensor is installed on the flying wheel panel, the RPM ratio is equal to the number of gears of the engine; If the speed signal takes from W-Terminal, the RPM ratio is equal to the half of the number of poles.

5. Normally, When the engine at idle state, tachometer shows 600-800rpm that means speed ratio is correct. If not, you can turn down or turn up speed ratio to check RPM difference.

How to set Odometer?

- Press the back button for 2-3 seconds first and then turn on the power supply.

- Release the button after seeing “ODO”; Press the button to set up the target odometer value.

- After adjustment, release button first, then wait for menu to complete flashing.

- Turn off the power supply, then turn on again. Odometer will record the setting.

How to set unit?

- Press the back button for 2-3 seconds first and then turn on the power supply.

- Release the button after seeing “UNIT”.

- Choose the unit you need (km/h, mph, knots)

- After adjustment, release button, and wait for menu to complete flashing.

- Turn off the power supply, then turn on again. Odometer will record the setting.

External button wiring?

For the external button, one pin is connected to gray wire of speedometer, the other to power negative/ground.


	200km/h 8000 RPM	200km/h 8000 RPM	999(MPH, Knots, KM/H adjustable)	200km/h 8000 RPM	999(km/h, mph, knots available)	999(km/h, mph, knots available)

Customer Reviews	—	1	—	25	70	317
Price	$87.99	$79.99	$65.99	$79.99	$63.99	$55.99
size	85mm	85mm	85mm	85mm	52mm	85mm
color	white+stainless steel	black+stainless steel	black+black	white+stainless steel	black+stainless steel	black+black
Indicating Range	0-200km/h 0-8000 RPM	0-200km/h 0-8000 RPM	0-999(MPH, Knots, KM/H adjustable)	0-200km/h 0-8000 RPM	0-999(km/h, mph, knots available)	0-999(km/h, mph, knots available)
adjustable odometer	no	yes	yes	yes	yes	yes
Type	GPS speedometer with tachometer	GPS speedometer with tachometer	GPS speedometer	GPS speedometer with tachometer	GPS speedometer	GPS speedometer