Feature

●100% MPPT 50A solar charge controller Intelligent, Max efficiency ≥98.1%, PV utilization ≥99%.Built-in DSP controller with high performance Automatic battery voltage detection 12V/24V/36V/48V, Make sure batteries voltage more than 12V to boost controller and make sure battery has enough power to Self-detection when connected to the controller.
●Fit for 12V/24V/36V/48V battery, USER(can be set Lithium, Lifepo4, Li(NiCoMn)O2)/Flooded/Sealed/Gel battery, User programmable for absorption voltage/Floating voltage/Low voltage disconnect./Load Timer.
●Built-in cooling fan, Fan will ON when temperature >45℃ and off < 40℃,Porous heat dissipation and fan use BEARING technologies increase life UP TO 5000hrs in normal use.
●Very detail display with Blacklight---LCD Dispaly PV voltage/output power/Battery voltage/charging current/working mode/Temperature
●TROUBLESHOOTING function and LCD display and can help users not only check the whole system operating data and statuses but also quickly identify system faults and modify parameters.


Description

mppt 50Amppt 50A

50A MPPT CHARGING PARAMETER

  • System voltage(battery voltage support): 12V / 24V / 36V / 48VDC Auto
  • Rated charge current: 50A / discharge current: 5A
  • Max Input Power: DC20V ~ DC80V (when battery is 12V) / DC37V ~ DC105V (24V) / DC50V ~ DC160V (36V) / DC72V ~ DC160V (48V)
  • NOTE: please dont exceed The maximum PV input power and voltage or will damage the controller.
  • Battery System Voltage: DC9V~DC15V (12V) / DC18V~DC30V (24V) / DC32V~DC40V (36 V) / DC42V~DC60V (48V)(In order to more accurately identify the battery system voltage, please make sure battery voltage is full when first wiring.)
  • Air circuit breaker and wires requirement, copper wires: 9AWG / air circuit: 100A

Notes: The output terminal is for lamp only (12V system less 60W, 24V/36V/48V system less 100W ), and it will be burnt if connecting to other loads. The output for battery is no polarity reverse protection.

50AMP SOLAR CHARGE FEATURE

MPPT solar charge controllerMPPT solar charge controller

Feature

  • 100% MPPT 50A solar charge controller Intelligent, Max efficiency ≥98.1%, PV utilization ≥99%. Built-in DSP controller with high performance
  • Automatic battery voltage detection 12V/24V/36V/48V, Make sure batteries voltage more than 12V to boost controller and make sure battery has enough power to Self-detection when connected to the controller.
  • Fit for USER(can be set Lithium, Lifepo4, Li(NiCoMn)O2)/Vented/Flooded/Sealed/Gel/NiCd battery.User programmable for absorption voltage/Floating voltage/Low voltage disconnect./Load Timer. Real-time energy recording.
  • ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers.
  • two terminals for PV positive, PV negative, battery positive and battery negative wiring, your can wiring them at the same time, or take one as backup terminal.
  • Blacklight LCD Dispaly PV voltage/output power/Battery voltage/charging current/working mode/Temperature.
  • Intelligence Fan-on temperature >45℃ and off < 40℃,Porous heat dissipation
  • Charging 3-stage: constant current(MPPT), constant voltage(Absorption Voltage), floating charge
  • Selectable battery type Vented / Sealed / Gel / NiCd / Lithium battery (default is Sealed) (defined voltage for other battery by user)
  • Soft start time ≤1S, Dynamic response and recovery time 100us
  • Max efficiency ≥98.1%, PV utilization ≥99%
  • In order to reduce the cost of electricity caused by high current, PV and battery each have two terminals
  • MULTIPLE ELECTRONIC PROTECTIONS

mppt 50Amppt 50A