Feature

●This BN-180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to gnd, green to txd, white to rxd.
●The TX LED flash means gps module output normally. The PPS LED flash means gps module locate your place.
●Data Level : TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
●This BN-180 GPS Module does not have FLASH and cannot be saved. 72 Searching Channel Support Rate : 4800bps to 921600bps, Default 9600bps.
●What you will get: 1 X BN-180 GPS Module


Description

Specification

Receiving Format :　GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS

Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1

Channels : 72 Searching Channel

Sensitivity:

Tracking : -167dBm, Reacquisition : -160dBm

Cold start : -148dBm, Hot start : -156dBm

Accuracy:

Position Horizontal : 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky)

Velocity : 0.1m/sec 95% (SA off)

Timing : 1us synchronized to GPS time

Acquisition Time:

Cold Start : 26s, Warm start : 25s, Hot start : 1s

Data and Update Rate:

Support Rate : 4800bps to 921600bps,Default 9600bps

Data Level : TTL or RS-232,Default TTL level

Data Protocol : NMEA-0183 or UBX, Default NMEA-0183

Single GNSS : 1Hz-18Hz Concurrent GNSS : 1Hz-10Hz,Default 1Hz

Operational Limits:

Altitude : 50,000m Max, Velocity : 515m/s Max

Acceleration : Less than 4g

Power consumption:

VCC : DC Voltage 3.0V-5.5V,Typical: 5.0V

Current : Capture 50mA/5.0V

Operating temp :　-40 °C to +85°C, Storage Temp : -40°C to +105°C

Indicator:

TX LED:blue.The data output, TX LED flashing

PPS LED:red.PPS LED not bright when GPS not fixed,flashing when fixed

Wiring:

GND,TX output,RX input,VCC(3.0v-5.5v)

BN-180 GNSS ModuleBN-180 GNSS Module

NMEA message output sample

GNRMC,073114.00,A,2237.56240,N,11401.59614,E,1.329,21.11,020916,,,A,V*37

GNVTG,21.11,T,,M,1.329,N,2.462,K,A*1B

GNGGA,073114.00,2237.56240,N,11401.59614,E,1,12,0.78,112.9,M,-2.5,M,,*54

GNGSA,A,3,19,05,02,06,17,12,09,13,,,,,1.48,0.78,1.26,1*01

GNGSA,A,3,69,83,84,70,68,82,,,,,,,1.48,0.78,1.26,2*0E

GPGSV,4,1,13,02,46,340,36,05,52,254,37,06,42,041,41,09,22,053,40,0*6E

GPGSV,4,2,13,12,32,282,35,13,13,185,33,17,36,131,37,19,57,119,44,0*66

GPGSV,4,3,13,20,03,237,,23,00,038,,25,09,311,19,42,51,128,32,0*60

GPGSV,4,4,13,50,46,123,33,0*50

GLGSV,2,1,08,68,25,027,39,69,78,011,36,70,40,213,43,74,00,259,,0*78

GLGSV,2,2,08,82,06,124,36,83,46,085,44,84,44,358,41,85,05,324,14,0*74

GNGLL,2237.56240,N,11401.59614,E,073114.00,A,A*7C

Beitian 180Beitian 180

betaflight softwarebetaflight software

Beitian 180 GPS connection to sensorBeitian 180 GPS connection to sensor

BN 180 GPS connection to flight controller

VCC to 5V

RX to TX3

TX to RX3

GND to GND

betaflight Software

Set up GPS module with betaflight Software

BN 180 GPS connection to sensor

VCC to 5V

RX to D4

TX to D3

GND to GND

BN-180 BN-220 BN-800 BN-880
BN-180 GPS BN-220 GPS BN-800 GPS BN-880 GPS
Model BN-180 BN-220 BN-800 BN-880
Flash No 4M Flash 4M Flash 4M Flash
Antenna Type Passive Passive Passive Active
Compass No No HMC5883L HMC5883L
Defaut Working Mode GPS+GLONASS GPS+GLONASS GPS+GLONASS GPS+GLONASS
Voltage 3.6-5.5V 3.6-5.5V 3.6-5.5V 3.6-5.5V
Default Baudrate 9600 9600 9600 9600
Frequency Range 1-10HZ 1-10HZ 1-10HZ 1-10HZ
Output TTL TTL TTL TTL
Pin Header GND,TX,RX,VCC GND,TX,RX,VCC SDA,GND,TX,RX,VCC,SCL SDA,GND,TX,RX,VCC,SCL

GPS Modules Comparison

GPS Modules Comparison:GPS Modules Comparison:

GPS Modules Comparison

BN-180 GPS Module Size: 18*18*6mm

BN-220 GPS Module Size: 22*20*6mm

BN-880 GPS Module Size: 28*28*10mm

BN-800 GPS Module Size: 35*35*6mm