Feature

●Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 55mm (2 3/16”) behind the panel to fit the gauge. Put the gauge in the hole and screw down.
●Connection: Black wire-GND, Red-power(+), White-external button(+), Red/Yellow-Backlight, Blue-Left turn, Green-Right turn, White wire-High Beam
●9-32V Working Voltage, Red and Yellow backlights available, Indication light: LEFT, HIGH BEAM, RIGHT
●Securely fasten GPS antenna, preferably outdoors (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. Do not cut cable
●OverSpeed Buzzer Alarm, Total Mileage Adjustable, Mileage Range: 0-999999 miles

Description

Product Features:

-Suitable for all vehicles and off-road vehicles

-The signal comes directly from the satellite signal receiver(GPS Antenna), don’t need other speed sensor.

-The gauge has the advantages of high precision, quick location confirmation and short start up time.

-IP67 waterproof and dustproof grade

-Reverse polarity protection and anti-fogging performance

-No Stationery Drift

-Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc.

Product Introduction


How to install it? - Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 55mm (2 3/16”) behind the panel to fit the gauge. - Put the gauge in the hole and screw down. - For the GPS antenna, you should securely fasten it in the flat position, black side upwards, preferably outside (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. And do not cut cable.	How to Set Odometer? - Press the back button for 2-3 seconds first and then turn on the power supply. - Release the button after seeing “ODO”; Press the button to set up the target odometer value. - After adjustment, release button first, then wait for menu to complete flashing. - Turn off the power supply, then turn on again. Odometer will record the setting.	How to change "BUZZ"? 1. Press the button for 2-3 seconds first and then turn on the power supply. 2. Release the button after seeing “BUZZ”; Press the button to set up the target overspeed buzzer alarm threshold value. 3. After adjustment, release button first, then wait for menu to complete flashing. 4. Turn off the power supply, then turn on again. Odometer will record the setting.

How does GPS Speedometer odometer compensation work?

When the device enters tunnel/bridge without no GPS signal, the inside flash memory will record the last valid GPS longitude and latitude.

And the device will get valid GPS longitude and latitude again when leaving tunnel/bridge.

The CPU inside will calculate the two GPS data to use algorithm to add the lost odometer when in tunnel/bridge.

Technical Data

Fixing dimension	85mm(3-3/8")
Indicating Range	0-125MPH
Working Voltage	12V/24V
Total Mileage Range	0-999999 miles
Trip Mileage Range	0-999.9 miles
OverSpeed Buzzer Alarm	Value Adjustable
Indication light	LEFT, HIGH BEAM, RIGHT
Backlight	Red and Yellow available
Working temperatures	- 40 to 85°C
Operation mode	LCD display, stepper motor

FAQ


NO. GPS speedometer keeps counting ? 1. After installation in the first time, GPS speedometer needs to search for signal, thats the reason that LCD counts numbers all the time. 2. After getting signal, LCD will come back to 0. It is normal.	NO. B07KPBYR7P How to switch Odometer & Tripmeter? The LCD will show Total Odometer as default. Quick press the back button to switch show Trip Odometer. Long press the back button to reset the Trip Odometer to zero.	NO. B07KPD78JS External button wiring ? For the external button, one pin is connected to white wire of meter, the other to power negative/ground.