Feature

●6 in Concrete Hole Saw with Hex Arbor with TCT Pilot Drill for Drilling Masonry Products and Recessed Light Installation
●152mm 6" CARBIDE GRIT HOLE SAW For Drilling Holes In Tough To Drill Materials, Regular Toothed Hole Drill Bit Would Go Dull If Used As A Drywall Hole Saw But With Carbide Tipped Tool Bits They Are Tougher And No Teeth To Snag And Go Dull.
●TILE HOLE SAW Drill Ceramic Wall Tiles And Low Density Subway Tile Without Hammer Drill Setting, When Used As Concrete Tools Hammer Drill Is A Must So The Tct Hole Saws Are Best Used With Our Hole Saw Abors That Already Come With Tct Masonry Drill Bits For Pilot Bit No Point Having A Hole Saw That Can Cut Holes In Brick If The Pilot Drill Set Will Not.
●7/16 Hex End Arbor for Hole Saws 1 1/4" to 6" inclusive - SDS Plus also available
●Removeable TCT Pilot Bit - can be change out for your own 1/4" HSS Drill if required.


Description

Tungsten Carbide Grit Edge Hole Saw and Accessories

Carbide Hole Saw Grit Edge TeethCarbide Hole Saw Grit Edge Teeth

Larger Arbors for Larger HolesawsLarger Arbors for Larger Holesaws

7/16 HEX MALE TO 7/16 HEX FEMALE ARBOR EXTENSION7/16 HEX MALE TO 7/16 HEX FEMALE ARBOR EXTENSION

7/16 Female to SDS Plus Male Arbor Extension7/16 Female to SDS Plus Male Arbor Extension

Carbide Hole Saws for Concrete and Drywall

Carbide Hole Saw Tungsten Carbide Grit Edge. Serrated Edged Teeth Hole Saw Capable of Drilling Concrete Drywall Brick and most Masonry Products. No Teeth to Dull and Bind. Must be used with Hammer Drill and TCT Tipped Pilot Drill.

Hole Saw Arbors with TCT Pilot Drills Are Suitable for These Size Carbide Hole Saw

Hole Saw Arbors / Mandrels Suitable for use with Larger Carbide Grit Hole Saws have Tungsten Carbide Tipped / Masonry Pilot Drills which can be swapped out for High Speed Steel Pilots if you use them on non Masonry Products Later. 7/16 Hex End Asin: B08NT2P715 OR SDS Plus End ASIN: B08NHMWY9S

7/16" Hex Female to 7/16" Hex Male 12" Hole Saw Arbor Extension

7/16" Hexagonol Ended Hole Saw Arbor / Mandrel Extension is Suitable with any 7/16" Hex End Arbor - Extends Drilling Capabilities an extra 12" Deep. Fits any regular 1/2" wide opening Drill Chuck. B08NHB1T2R

7/16" Hex Female to SDS Plus Male 12" Hole Saw Arbor Extension

The SDS Plus Male end of this Arbor / Mandrel Extension Means this Arbor must be used with an SDS Plus Type Drill. The Female end that Connexts to the Hole Saw Arbor is a 7/16" Hex End so the Hole Saw Arbor must Also have a 7/16" Hex End - Extends Drilling Capabilities an extra 12" Deep. Fits SDS Drill Chuck Only. B09S8MHFN2

Tungsten Carbide Hole Saws Material Cutting

Carbide Hole Saw with Concrete Block and SDS DrillCarbide Hole Saw with Concrete Block and SDS Drill

Holes in Concrete and PaverHoles in Concrete and Paver

Holes in Multiple ProductsHoles in Multiple Products

3 1/4 inch Carbide Hole Saw3 1/4 inch Carbide Hole Saw

Holes in Cement Block

Must use Hammer Drill and Must use TCT Pilot Drill for all Masonry Products.

Holes in Concrete Pavers Block and Coping

For Deep Holes Break Core out when Hole saw bottoms at 1 1/4" Deep, this allows Hole Saw to continue. Regularly check for TCT Pilot Drill not worked loose, a loose pilot will prevent the hole saw from cutting.

Cut Hardie Board Drywall Marble Slate Cement Board Drywall

Pilot Drill can be replaced and or swapped out for a HSS Pilot Drill if Drilling non Masonry Products like Plywood. TCT Pilot Drills are only for Masonry Products.

Serrated Teeth Covered with Tungsten Carbide Grit

Can be used with SDS Plus or Hex Arbors.

TCT Pilot DrillTCT Pilot Drill

Carbide Hole Saw TeethCarbide Hole Saw Teeth

7/16 Hex Hole Saw Arbor7/16 Hex Hole Saw Arbor