Feature

●For detecting NPN and PNP transistor, capacitor, resistor, diode, triode, N-channel and P-channel MOSFET, IGBT, JFET, triac and battery, resistor and capacitor and other components, etc.
●Put the pins of component in corresponding area, then dial the little handle and the detector will test it automatically, finally the results will display on the back light TFT screen clearly. ( Use 12864 liquid crystal display with green backlight).
●After detection, align the infrared remote control with the "IR" light, then press the button in the remote control, if the detector successfully decode it, it will display the data code and infrared wave form.
●Measurement results represent by TFT graphic display(160x128). Support Chinese and English.
●One key operation, Auto Power Off(Timeout Settable). Can also press the multi-functional button to close the detector.

Description

It can be widely used to detect NPN and PNP transistor, capacitor, resistor, diode, triode, N-channel and P-channel MOSFET, IGBT, JFET, triac and battery etc.
It can also be used to detect infrared wave forms.
It also can detect zener diode and has the function of self-calibration.
After detection, align the infrared remote control with the "IR" light, then press the button in the remote control, if the detector successfully decode it, it will display the data code and infrared wave form.
One button operation, automatically detect and shutdown, and you can press the multi-functional button to close the detector too.
Put the pins of component in corresponding area, then dial the little handle and the detector will test it automatically, finally the results will display on the back light TFT screen clearly.
Not like the usual black and white display, this detector will show results in color.

1x Transistor tester 1 x Cable (random) 1 x Electronic Component Set (random) 3 x Test Hook(random)

Specifications

Display: 1.8inch TFT Screen

Diode Range: < 4.5V

Zener Diode:Transistor Detect Area: 0.01-4.5V

Zener Diode Detect Area: 0.01-30V

Triac Range: IGT < 6mA

Capacitance: 25pF-100mF

Resistor: 0.01-50M?

Inductance: 0.01mH-20H Battery: 0.1-4.5V Power Mode: Rechargeable Lithium Battery (NO included)

Notes: Please allow 1-3mm error due to manual measurement.
Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!

Operating Instructions

Multi-function key has two actions:

Short press: Press the key and not less than 10 ms, release key within 1.5 seconds

Long press: Press the key more than 1.5 seconds

Power on

In the power off state, short press the multi-function key, the tester is turned on and automatically measured.

In the power off state or the test is completed, put the test element into the transistor test area of test seat, and press the locking handle, short press the multi-function key, the tester automatically measure, graphical display of measurement results when testing is complete.

Warning: Always be sure to DISCHARGE capacitors before connecting them to the tester! The tester may be damaged before you have switched it on!

Warning: We do not recommend using the tester to measure the battery! The battery voltage must be less than 4.5V, otherwise the tester may be damaged!


Transistor Tester - Automatic detection of zener diode 0.01-30V - Self test with automatic calibration	IR Decoder - Support Hitachi IR coding - IR waveform display - Infrared receiving instruction	Other - Measurement results using TFT graphic display(160x128) - One key operation - Auto Power Off(Timeout Settable)


IR decoder After the component detection is completed,the infrared remote control at the tester"IR" test hole, press the remote control key,the tester will be display the user code&date code and the corresponding infrared waveform after the successful decoding. If decoding failure,the tester cannot display the user code and date code. The dot at the top right corner to indicate whether it has received the remote control infrared date,red represents infrared date is being received,blue represents decoding success.	Built-in Li-ion Battery Voltage Measurement The built-in Li-ion Battery voltage is measured before detection,when the battery voltage is less than 3.0V will force shutdown,then please charging.	Charging the Battery The tester has a standard Micro USB interface,please use an external 5V power supply or USB power charging.

Specifications

Transistor Tester

IR Decoder

Other

IR decoder

Built-in Li-ion Battery Voltage Measurement

Charging the Battery