Feature(may vary by option.)

●Ideal glue for the installation of smooth/unthreaded cylindrical metal assemblies: 1,Fill the voids and reduce the precision requirements of design, production and installation; 2,Prevent assembly from loosening, wear and corrosion; 3,Evenly distribute loads and stresses during assembly; 4,Sealed from oxygen and other contaminants. Extend the life and safe use of the equipment!
●High Strength: After complete curing, Shear strength can be comparable to that of metal materials (609 ≈ Aluminum, 620 & 680 ≈ Copper, 603 & 638 ≈ %0.1 C Steel, 648 ≈ %0.2 C Steel), Ensuring efficient and stable operation of the equipment. Needs to be heated to 250 ℃/482℉ when disassembling, and mechanical auxiliary equipment is required.
●Applicable Scope: Suitable for the assembly of any smooth, unthreaded cylindrical metal components, Such as keys and shafts, bearing, rotor shaft, bushing, casing, cylinder liner, key slot, valve sleeve, movement sleeve, valve bushing etc. Choose the appropriate use according to the characteristics of different models.
●Applicable Material: Suitable for all kinds of solid metals, even metals with active surfaces such as iron, copper, brass, steel, etc. not to mention metals with inert surfaces such as stainless steel, aluminum, gold, etc.
●Simple Use: Just apply the product evenly to the fixed location, the product will start curing within 60 minutes after the assembly is installed, and it can be used normally after 24 hours of standing.
●Function: Fill gaps between components / Lock components to prevent loosening / Prevent component abrasion & corrosion / Improve the accuracy of component fit / Isolate oxygen and prolong product life / Tightness to prevent leakage / Evenly distribute loads and stresses / Repair minor defects in parts / Reduce design and process complexity

[242]




[243]




[620]




[603]




[648]




[242   &  271]




[638]




[271]




[680]




[609]





Description

Brief Introduction to ESKONKE Retaining Compound

ESKONKE retaining adhesive can improve the shear strength of cylindrical unthreaded assembly operations.

The holding adhesive has the ability to transfer loads to the maximum extent and can evenly disperse them, eliminating stress concentration and corrosion at the assembly interface.

As a liquid application, holding adhesive can achieve 100% bonding on two metal bonding surfaces, reducing the cost of improving part processing accuracy and improving assembly process efficiency.

603 609 620 638 648 680
Retaining Compound 603 Retaining Compound 609 Retaining Compound 620 Retaining Compound 638 Retaining Compound 648 Retaining Compound 680
Shear Strength 3770 psi 2300 psi 2500 psi 3625 psi 4480 psi 2880 psi
Glue Viscosity(77℉) 100 ~ 150 mPa.s 110 ~ 140 mPa.s 5000 ~ 12000 mPa.s 2000 ~ 3000 mPa.s 450 ~ 550 mPa.s 750 ~ 1750 mPa.s
Viscosity Grade Low Viscosity Low Viscosity High Viscosity Medium Viscosity Low Viscosity Medium Viscosity
Viscosity Thixotropy ✓
Maximum Filling Gap 0.13 mm 0.13 mm 0.38 mm 0.25 mm 0.13 mm 0.38 mm
Initial Curing Time 10 min 10 min 60 min 4 min 4 min 10 min
Curing Time 24 Hours 24 Hours 24 Hours 24 Hours 24 Hours 24 Hours
Operating Temperature Range -65 ~ 302 ℉ -65 ~ 302 ℉ -65 ~ 450 ℉ -65 ~ 356 ℉ -65 ~ 356 ℉ -65 ~ 356 ℉
ANTI-OIL ✓ ✓ ✓ ✓ ✓
Corrosion/Chemical Resistance ✓ ✓ ✓
222214222214

Why do you need it?

  1. Fill Gaps Between Components
  2. Lock Components to Prevent Loosening
  3. Prevent Component Abrasion & Corrosion
  4. Improve the Accuracy of Component Fit
  5. Isolate Oxygen and Prolong Product Life
  6. Tightness to Prevent Leakage
  7. Evenly Distribute Loads and Stresses
  8. Repair Minor Defects in Parts
  9. Reduce Design and Process Complexity

456456456456

PRECAUTIONS

  • Curing conditions: metal material; air isolation; Gap is lower than the maximum gap;
  • Make sure the components are at room temperature, dry and clean. The cleaning solvent can use trichloroethane, trichloroethylene, methyl ethyl ketone, methanol, etc. It is not suitable to use gasoline, kerosene, fuel oil, hydrocarbon solvents, etc., which are easy to leave an oil film on the metal surface;
  • Grinding the metal surface that needs to be bonded is beneficial to improve the bonding strength;
  • Not suitable for use in pure oxygen or oxygen-enriched environments, and cannot be used as a sealing material for chlorine or other oxidizing substances;
  • Not suitable for bonding porous materials such as plastic, wood, paper, etc. For active metals such as steel, copper, and alloy metals, it has fast curing and high strength, and for inert metals such as stainless steel, zinc, and cadmium, it has slow curing and low strength. Please understand product compatibility before use;
  • When dismantling, it can cooperate with mechanical auxiliary equipment and heat the components to 200~300°C (392~572°F), or it can be dismantled after soaking with special scavenger for a long time;
  • Seal as soon as possible after use to avoid volatilization of active ingredients;
  • Do not pour the unused glue back to avoid contamination;
  • Do not replace the storage container during storage. In order to avoid curing during transportation, the actual capacity is only half of the bottle capacity;
  • Store in cool/normal temperature (8~21℃/46~70°F), avoid sunlight.

Whats in the box

  • Bottle

    • Product guides and documents

    Safety Information (PDF)