Feature

●Backup camera flush mount with a LATEST 6pcs FULL glasses large-aperture optical system,the picture with very low distortion rate,you will get crystal realistic view when you backing up. Also it with a horizontal 135 degree wide view angle lens,its great for you to check the invisible blind spot clearly and make parking safe and simple.
●Rear view camera surface mount support IP69K waterproof IP rate. It designed with fully sealed glue filling craft, so the waterproof effect is better than IP67 and IP68, you absolutely no need to worry about water, fog or mist inside. NOTE: please separately order a suitable harness to complete installation if connect it to a FACTORY RADIO.
●Reverse camera flush mount support both CVBS and AHD video signal output(great for Android stereos).CVBS by default,cut the purple wire loop to choose AHD format video signal (AHD,720P,30fps). It with starlight level night vision (0.005Lux,excellent low-light performance),you never worry about parking during night, rainy day or in dark garage.
●Car backup cameras housing is metal,2 in 1 installation option design(surface or flush mount option).Also it is built in 3 multifunctional switching loops: cut the white loop for front view, cut the green loop to remove the guidelines and cut the purple loop to choose AHD format(AHD,720P,30fps)video signal output.
●Beware: According to our experience, some cheap or old Android stereos have the setting of AHD format video signal input option, but the truth it does not work, because their hardware inside do not support it. If so, please use the default CVBS video signal output (do not cut the purple wire loop, otherwise you will get a black screen).
●This backup car camera flush mount doesnt fit sucked type dash cam and mirror dash cam, because these dash cam have different connectors and inside PIN definition, even some of them with same size 4 PIN connector. If connect this hitch flush mount backup car camera to a GPS navigator, such as Garmin or TomTom, please separately order one more adapter which with a RCA to 2.5mm connector to complete installation.
●Before you cut this flush mount car backup cameras purple wire loop to choose AHD format 720P 30fps video signal output, please make sure your Android stereos support AHD format video signal input first(most of old Android stereos do not support it,and it works well on selected ATOTO car stereos (work well on F7 Series, S8 series and A6 KarLink version,can not work on ATOTO A6Y Series Android stereo or SA102 Starter).
●NATIKA offer 30 days money back guarantee,24 months replacement warranty,lifetime support guarantee and 7 days-24 hours customer service and technical support.


Description

As a burgeoning manufacturer of top-notch OEM&ODM vehicle electronic products, NATIKA aims to serve even the most demanding needs of worldwide clientele.Invariably, we believe that customer experience counts far more than short-term profits, so we make concerted efforts to design, manufacture, and improve our products and services in an innovative and responsible fashion.

NATIKA backup camera WD-012 support flush or bracket mount option, no distorted & fish-eye effect, starlight level night vision,IP69K IP rating reliable waterproof and horizontal 135 degrees wide view angle.

Useful Wire/Loop Control Design:

Reverse camera WD-012 with 2 small wires/Loops (White and Green color).

*If you need the guide line, please keep the green loop; If no need, just cut it; If you use it as a front view camera, please cut the white loop;

*If you use it as a front view camera without guide line, please cut both white and green wire/loop; If as a side view camera, please rotate the middle housing part of the camera (maximum 360 degrees) to get a prefer view angle; Look backward, keep the white loop; look forward, cut the white loop.

*Note: this camera is a rear view camera with guide line/parking line as DEFAULT.

*Please power on again after you cut the small loops, then the image should be correct.

What you get:

1 x NATIKA Backup Camera; 1 x 26ft/8M Extension Wire; 2 x 304 Stainless Screws; 1 x Double Tape; 1 x User Manual; 1 x Electrical Tape; 3 x Wire Clamps; 1 x Panel Remover; 7 x Zip Ties; 1 x NATIKA Gift Box; 1 x Thanks Card; 1 x 0.886in/22.5MM TCT Hole Saw; 1 x 304 Stainless Bracket; 1 x Metal Front Housing

Notes:

*This NATIKA rear view camera WD-012 is perfect for REAR, FRONT and SIDE view.

*If connect this NATIKA backup/front/side view camera WD-012 to a FACTORY RADIO, please separately order a suited Harness & Programmer to complete installation, because different RADIO need different Harness & Programmer to work together.

* Mount this reverse camera on the panel and route the wire to inside (DO NOT pinch the wire/cable when route the wire, pinched wire will damage the camera, drill a hole to allow the wire go through if needed).

* If your head unit with a reverse triggering wire, normally it is a purple/white, blue/white or pink color wire, please find it, and connect it with the extension wires triggering wire well(small short red wire next to the RCA/AV connector).

*If the image on the screen is blurry, flickering/flash or has horizontal or vertical strip, please check all your power and video connections. Possibly use a different ground point(iron part) and wrap power and video plugs with electrical tape to insulate from interference. If it still with blurry, flickering/flash or has horizontal or vertical strip, please order a 12V DC power adapter filter rectifier to solve it, especially need for Dodge VW AUDI BMW Mercedes Benz brands vehicle.

*Before you routing, if there is no image on the screen, other than check the camera, please check display setting as well. You can use other device with RCA connector, such as TV to check if the camera works.

* If you use wire clamps for connection, please kindly check and see if it works(connection is solid or not).

*For camera connection: connect the cameras male plug to female connector of the extension wire/cable, make sure the arrows to align and push the cameras male plug tightly into the female connector of the extension wire.

*If the camera is mounted offset, the guidelines on image will be offset.

*Ideally to mount the camera at the middle of the trim. If mount the camera at side, it still works, but with guide line offset.

*Guide line is for reference only, please use the mirrors for position when backup.

*Apply electrical tape for the joint of all for the connectors, and use zip ties to fasten the wire on your vehicle.

*Seal the red wire next RCA/AV connector with electrical tape if you do not use it.

*If you want to get a perfect view angle, before you use a drill rig to make a hole, please seriously check and test to find where is the best spot to mount this reverse camera,please rotate the middle housing part of the camera (maximum 360 degrees) or move the bracket (maximum 90 degrees) to get the best view angle.

backup camera for carbackup camera for car
back up camera for trucksback up camera for trucks

back up cameraback up camera

rear view camerarear view camera

reverse camerareverse camera

High Resolution and Amazing Night Vision

NATIKA vehicle reverse camera WD-012 built-in a LATEST high sensitive STARLIGHT LEVEL night vision HD 1/2.7inch CMOS IV image sensor and a digital high-definition image processor ISP(support 3D digital noise cancelling technology) it is maximum Pixels 1280*720, and effective 960*576 pixels at 25 fps, also with grade A 6G All-glass,F1.8 large aperture lens, transmit great sharp and clear image in day and night. Base on different output format, the rear view camera WD-012 output is 600TVL, but it is clear than the cameras whose original resolution is 420TVL,480TVL, 520TVL and 600TVL. It support amazing night vision function, the minimum illumination is 0.005Lux, say goodbye to grainy picture!

IP69K High IP Rate Waterproof

IP69K waterproof IP rate NATIKA rear view camera WD-012. It designed with fully sealed glue filling craft, so the waterproof function is better than IP67 and IP68, no need to worry about water, fog or mist inside.

Wide Applicable Temperature

NATIKA vehicle rear view camera WD-012 built-in wide range temperature electronic parts and components, the range is from -22℉ to +185℉(-30℃ to +85℃), it is great weatherproof and can work perfectly not only in the high temperature summer but also in cold winter or snowy weather, also outlasts harsh weather like thunderstorms, rain and more, in short it can adapt to all kinds of bad weather.

back up car cameraback up car camera

rv backup camerarv backup camera

rear camerarear camera

No Distortion & Fish-eye Affect REAL Picture

NATIKA flush or bracket mount vehicle reverse camera WD-012 use a LATEST 6pcs FULL glasses large-aperture optical system(include a grade A 6G All-glass+F1.8 large aperture lens),so the picture without any distorted & fish-eye effect, you will get a 100% REAL picture when you backing up, and enjoy a FULL REAL picture!

Small size MINI 4PIN connector

NATIKA vehicle reverse camera WD-012 with small size，diameter is 0.886in and solid materials grade A zinc alloy housing.

5MM mini 4PIN connector for convenient installation.

Amazing Night Vision

NATIKA vehicle backup camera WD-012 shows you clear picture even very dark areas, such as out of doors at night or inside of garage, because it built-in a latest 1/2.7inches low illumination level 0.01Lux high sensitive CMOS sensor and a Digital high-definition image sensor processor(ISP), also with a grade A 6G All-glass and F1.8 large aperture lens, delivers sharp and crystal clear picture day and night.

rear backup camerarear backup camera

car backup cameracar backup camera

rca backup camerarca backup camera

0.886in/22.5MM Sturdy & Solid TCT Hole Saw

NATIKA flush mount front view camera WD-012 include a sturdy and solid tungsten carbide tip hole saw, It can pierce less than 0.315in/8mm stainless steel plates or less than 0.7874in/20mm metal plates very well. And HSS(High-Speed-Steel)hole saw only can pierce less than 0.118in/3MM cast iron, aluminum, plastic or wood materials plates.

Useful Wide View Angle

NATIKA flush or bracket mount vehicle rear view camera WD-012 built-in a LATEST Grade A 6G All-glass and F1.8 large aperture lens, the lens horizontal angle is 135 degrees(visible range up to 95%), thanks to the 135° viewing field, youll be able to see far more than you could in the rear view mirrors alone. It helps you to decrease blind zone accidents very well.(your kids and pets will be more safe behind or in front of your vehicles).

Easy Installation

1. Find a flat surface for mounting camera 2. Connect the power wire of flush mount backup camera to power of reversing light 3. Connect the 26ft extension cable of flush mount backup camera to the head unit of vehicle.

NOTE: 1).Please test the backup camera before routing 26ft extension cable from back to front.

2).Connected trigger A with B if your head unit with a trigger wire A, If not, no need connect them.

4.Start the vehicle and gear on reverse to test the camera.

5.Re-install the head unit.

Product information