Feature(may vary by option.)

●♞【23HS8430 Nema23 Stepper Motor】Nema23 57 stepper motor;Step Angle: 1.8°; Current: 3.0A; Holding torque: 180N.cm/18kg.cm/270oz-in; Shaft : 8mm single shaft; Wiring:A+ : Red; A- : Green; B+ : Yellow; B- : Blue; Motor Size: 57x57x76mm
●♞【Driver】TB6600 driver Voltage: DC 10V-45V; Current: rated maximum output reaches: ±4.5A ; Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.
●♞【4 Axis USB Mach3 Control Board】USB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface. This control board does not require any drivers to be installed. As long as Mach3 can run, the control card can be used; Support computer system:Windows 2000/ XP / Windows 7/8/10; Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;
●♞【350W 24V DC Switching Power Supply】AC input voltage range: 110V-120V AC or 220V-240V AC; selected by switch to choose input voltage.
●♞【Functions of the Control Board】Can support the limit switch, emergency stop switch, auto tool zero, home switch etc.Support for connecting electronic handwheel.Have 0-10V signal output ,you can use mach3 software to control the spindle motor speed,can drive four relays for controlling the spindle starts, forward rotating and reverse rotating,pumps or other device.

[4-Axis-A]




[3 Axis-B]




[4 Axis-B]




[4 Axis-A]




[3 Axis-C]




[3 Axis-D]




[4 Axis-D]





Description

3 Axis Nema23 Stepper Motor Driver USB CNC Controller Kit

11

Parcel include:

  • 3× 23HS8430 Nema23 stepper motor 76mm 270oz-in 3A
  • 3× TB6600 stepper motor driver
  • 1× 4 Axis USB Mach3 control board
  • 1× USB Cable
  • 1× 350W 24V DC switching power supply
  • 1× CD disc

23HS8430 Nema23 stepper motor

11

22

33

  • Frame Size: 57 x 57 x 76 mm
  • Body Length: 76mm
  • Number of Leads: 4
  • Weight: 1.1kg
  • Single shaft is 8mm diameter,21mm length

* Motor Type: Hybrid

* Step Angle: 1.8 degree

* Holding Torque: 1.8Nm (270oz.in) 18kg.cm

* Phase Resistance: 1ohms

* Rated Current/phase: 3A

* Inductance:3.5mH+/-20%(1KHz)

* Frame Size: 57x57x76 mm

* Phase: 2 phase

* Insulation class: B

  • Stepper motors red wire connect to drivers A+ port
  • Stepper motors green wire connect to drivers A- port
  • Stepper motors yellow wire connect to drivers B+ port
  • Stepper motors blue wire connect to drivers B- port

TB6600 stepper motor driver

22

  • Suitable for Nema17 Nema23 two-phase/four-phase/four-wire/six-wire stepper motors which currently within 4.2A.
  • The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.
  • The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.
  • The motor rotates forward when CW is high or suspended, and reverses when it is low.
  • When EN is onhigh or floating, it is working state, when it is on low, it is offline.

22

w2w2

22

  • It adopts the common anode input mode, there are two input terminals, the wiring is more convenient;
  • The working voltage is DC 10V-45V. recommended DC 24V;
  • Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.
  • Using Toshibas new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.
  • The rated maximum output reaches: ±4.5A.The output current is steplessly adjustable.

Subdivision

  • full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.
  • Automatic half-flow function
  • Adopt enlarged radiator, good heat dissipation
  • With output short-circuit protection function.

Wirings between driver & mach3 board (for example X-axis):

Drivers "CLK-" connects to control cards XP pin

Drivers "CW-" connects to control cards XD pin

Drivers "5V" connects to control cards 5V pin

Note:

The power supply cannot be connected reversely, otherwise the chip will be burnt out.

The set current should not exceed the rated current of the motor.

4 Axis USB Mach3 Motion Control Board

33

33

33

  • Support for 4 Axis linkage, you can connect four stepper motor drives or servo drives;
  • Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;
  • Have 0-10V signal output,you can use mach3 software to control the spindle motor speed.
  • One status LED, indicate connection status on the board.

  • Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.
  • Support for connecting electronic handwheel;
  • MCU model: three generation 32-bit STM processor
  • Communication plug-in: RnR motion control card - ECO-2.0

  • 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.
  • 4 general-purpose inputs, you can connect the limit switch, estop switch, probe , back to zero and other device.

Wiring diagrams

11

Please strictly follow the instructions and warnings before using this product:

  • It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.
  • The output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface.
  • This interface can output 0-10V analog signals
  • USB interface is applicable to any netbook, notebook, desktop, tablet and other PC compatible computers with USB interface.
  • This control board does not require any drivers to be installed,as long as Mach3 can run, the control card can be used;
  • Support computer system: Windows 2000/ XP / Windows 7/8/10
  • The inverter interface (AVI +, AVI-) is isolated from the computer and the main control circuit, and has strong anti-interference ability,no interference signal will be introduced due to the introduction of external strong electrical equipment.
  • Whether frequency converter is supported: Yes
  • Support PWM: Yes
  • Number of control axes: X.Y.Z.A axis

350W 24V DC switching power supply

power supplypower supply

33

55

  • DC output voltage: 24V
  • Output current: 0-14.5A
  • Inlet stability: ±0.5%
  • Load stability: ±0.5%
  • DC voltage of Adjustable range: ±10%
  • AC input voltage range: 110V-120V AC or 220V-240V AC; 115VAC/6.5A/50HZ or 230VAC/3.4A/60HZ; Selected by side switch.

  • Working Temperature: -10℃～+50℃
  • Setup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full load
  • Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute
  • Isolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ

  • Four fold protection settings, multiple protections, stable performance, effectively reducing the impact of AC input.
  • Dual ball cooling fan and all metal casing design
  • It has the characteristics of fast speed and good performance, which can ensure the temperature operation of the equipment and extend its service life.
  • The shell is made of aluminum alloy and has a high thermal conductivity system, which is reinforced and durable, and the design is more user-friendly.
  • Short circuit protection: when the output terminal is short circuited, the power is turned off and the output voltage is 0V.
  • Overcurrent protection: when the output current is>115-150%, the output voltage is turned off.
  • Overload protection: power protection when the load power is greater than 105-135% of the rated power.
  • Temperature protection: the power supply is automatically protected under high temperatures.