Feature
●JAOAJO Squeaky Floor Repair Kit - #3251 Floor Screws for Use with #3233 Floor Squeak Elimination Kit . The screw is scored so when driven through the fixture it snaps 1/4" below the top of the hardwood.between the floor and joists.
●Box of 1 - Contains 5 Tools and 50 Screws, Eliminate Floor Squeak Through Carpet, Fix A Squeaky Floor,Squeak No More Floor Screws.JAOAJO#3233 Eliminates Squeaks Between Floor Boards and Joists No More Squeek Kit with #3251 Floor Screws.
●Beautiful box packing design, easy to store and use，Eliminate Squeaks Under Carpeted Floors, Hardwood, Vinyl, and Linoleum Floors.
●Suitable for all types of carpet and hardwood floors. Do not rock the screw head back and forth to minimize floor damage. Squeaky floor repair screws must be spaced close enough together. If you still have a squeak, put more screws on the joist line.
●Wax coated for easy driving，Scored to snap perfectly every time.
Description
JAOAJO Squeaky Floor Repair Kit with 5 Auxiliary Tools and 50 Count #3251 Floor Screws for Wood Floors Eliminate Squeaks Under Carpeted Floors
THIS KIT CONTAINS:
● An alignment and depth controlfixture part 3240.
●50 special scored screws,part #3251.
● Square head driver bit with astop,part #3261.
● Joist finding screw #3255.
● Hardwood Floor Adaptor
● Instructions
JAOAJO Squeaky Floor Repair Kit Application scenario
|
|
|
|
|---|---|---|
JAOAJO Squeaky Floor Repair Kit Application scenarioJAOAJO Repair Kits effectively repair squeaky floors - Squeaky no longer kits are specifically designed to stop floors from squeaking. Screws secure the floor to the joists, then effectively eliminate the squeaking between the floor and joists and return to a quiet environment. |
JAOAJO Squeaky Floor Repair Kit Application scenarioInstructions for Carpeted Floors overPlywood or Chipboard Locate the floor joist using the Joist Finding Screw. Then push the Alignment and Depth control fixture firmly into the carpet. Squeaks in Stairs Stairs hace three components:the stringer or carriage,the tread,and the riser. The stringer is the notchedboard to which the tread and riser are attached. Thesqueak is usually caused by the nails used to holdthe tread to the stringer or riser becoming loose. Tofix the squeak,place the alignment fixture over theconnection between the stringer and the tread orthe tread and the riser. Then drive the scored screwdown as far as the fixture will allow it to go. Use thescrew gripper to snap off the top of the screw. |
JAOAJO Squeaky Floor Repair Kit Application scenario1. The JAOAJO system will eliminate most squeaks under carpet,hardwood,vinyland linoleum floors. There can be cases where all squeaks cannot be completelyeliminated. This points to floor damage due to misapplication of the sub floor,water damage,structural damage,mechanical damage and other causes. Thesecases should be referred to a carpenter or floor professional to prevent furtherdamage. 2. Normally more than one screw is needed. It is best add additional screwsalong the joist,spaced approximately 4 inches. 3. Always use safety glasses and use in well lighted areas. 4. Snap off the screw heads at the end of the project,and thoroughly inspectthe area to insure all of the screw heads are removed. |
Tips on Squeaks
Tips on Squeaks
Tips on Squeaks:
Most squeaks in floors are caused by nails used in constructing the floor working loose andrubbing on the floorboard when you step on the area. Because of this the sooner you caneliminate the squeak the better. Young squeaks are much easier to correct than old timers,which have been allowed to grow.
Mechanical squeaks are caused by the floor rubbing on the cold air return or the floor flex-ing and rubbing on a pipe or electrical line. These are identifiend by a mechanical noisewhen you step on the area. JAOAJO can correct these in many cases by tightening the floorand by eliminating movement in the floor members.
JAOAJO Joist Finding Screw
The JAOAJO Joist Finding Screw is an easy to use tool that will find the exact locationof your floor joists from above the floor. The screw is designed to work on carpetedplywood or chipboard floors.
The screw is not designed to find the joist under hardwood floors. Each plank in a hard-wood floor has nails in it. The nails,in general,cause the squeaks. With hardwood floors,you need to drive the screws down into the plank that is visibly moving or where the noiseis coming from,not necessarily into the joist.
On plywood or chipboard floors,the nails are driven into the joist to hold the floor down. Over time,the nails loosen and allow the wood to move back and forth on the smooth shankportion of the nail. On this type of floor we use the Joist Finder,find the joist,and fasten thefloor to the joist.
*When working on a berber or loop carpet cover the short section of thread withtransparent tape. This will prevent the screw thread from touching the carpte fiberand possibly pulling a strand. Pile carpet this is not necessary.
Step 3. Measure 9 inches from a wallthat is parallel to the direction of the joist. This is a good starting point that should bevery close to the joist. Or if you have a heatvent in the floor you can use that to find thejoist. The vent is always between two joists. If you were to start next to the vent you willprobably find the joist on the first or secondattempt. Drive the Joist Finding Screw downinto the fioor 2 inches.
Instructions for using JAOAJO
Instructions for using JAOAJO
1. The JAOAJO system will eliminate most squeaks under carpet,hardwood,vinyland linoleum floors. There can be cases where all squeaks cannot be completelyeliminated. This points to floor damage due to misapplication of the sub floor,water damage,structural damage,mechanical damage and other causes. Thesecases should be referred to a carpenter or floor professional to prevent furtherdamage.
2. Normally more than one screw is needed. It is best add additional screwsalong the joist,spaced approximately 4 inches.
3. Always use safety glasses and use in well lighted areas.
4. Snap off the screw heads at the end of the project,and thoroughly inspectthe area to insure all of the screw heads are removed.
Instructions for JAOAJO
In general there are two types of carpeting Pile and Berber. Berber is madewith a series of loops from one continuous strand of fiber. When workingwith Berber carpet use a screw that has its tip and thread covered with a trans-parent household tape. It is important to use a taped screw on Berber carpetbecause it shields the screw threads from grabbing the carpet fiber. After youtape the screws follow the instructions below.
How to Find the Joist
in Hardwood Floors
If you have a stud sensor,use that to see if you can getan indication of the joist. If that works,pre-drill a holeat the joist through the hardwood with a l/s drill bit. Then drive the screw through the fixture,hacing the flatwide base against the floor. The screw will snap,³/s ofan inch below the surface. Then fill with a matchingwood filler.
If the stud sensor doesnt work,then near the wall onthe floor,pre-drill a small hole down 2 /inches,usinga³/zdrill bit. Take a straightened out paperclip and putit down the hole. If the paperclip goes down more than2 /₄inches,you are not in the joist. Move over an inchand do it again until the paperclip stops at 2 /4 inches,indicating the joist.
The holes that are made are very small. Because theyare close to the wall they will be very hard to see whenconcealed with filler.
|
|
|
|
|
|---|---|---|---|
50 specific scribing screwsFOR CARPETED FLOOHS Step 1.In the area of the squeak,find the joist fromabove the floor using the Joist Finding tool inthe kit.Then push the Alignment and DepthControl Fixture fimly into the Carpet. Step 2.Using the drver bit provided drive the screwdown as far as the fixture will allow. Step 3.Slip the Screw Gripper over the screw headand rock the fixture left to right,snapping thehead off.The screw breaks at the score that isset slightty below the wood of the floor. Step 4.There is no damage to the carpet and nothingto feel with your bare foot. |
joist search screws *2;square-headed drive drill *1;FOR HARDWOOD FLOORS Step 1.Pre-dril ahole in the floor witha 1/8 inch drill bitdown 21/4 inches. Step 2.Drive the screw through the shorter opening in the fixture. Step 3.The thread patten on thescrew pulls the wood tight together. Step 4.The head ofthe screw will hit thetop of the fixture.Thescrew will then pulland snap at the score. Step 5.The score is now set 1/5 of an inch below the wood.Fill the hole with putty to finish. |
Double-hole jig*1,Tripod calibration and depth control fixture*1WARNING:Always use safety glasses. WARNING:Use in well lighted areas,use work lights if necessary. WARNING:Keep out of reach ofchildren,and store in a secure place. |
JAOAJO Squeaky Floor Repair KitWARNING:This is engineered towork with the components provided. Any attempt to substitute parts cancause damage to the floor and maycause injury to the user. |
|
|
|
|
|
|---|---|---|---|
The JAOAJO Floor Squeak Repair Kit is suitable for all types of wood flooring, carpeted flooring, hardwood flooring, cork/vinyl flooring and linoleum flooring.If you are bothered by your squeaky floors, this squeaky No More JAOAJO Floor Squeaky repair kit will be an effective solution. JAOAJO Repair Kits effectively repair squeaky floors - Squeaky no longer kits are specifically designed to stop floors from squeaking. Screws secure the floor to the joists, then effectively eliminate the squeaking between the floor and joists and return to a quiet environment. |
The JAOAJO Floor Squeak Repair Kit is suitable for all types of wood flooring, carpeted flooring, hardwood flooring, cork/vinyl flooring and linoleum flooring.Most squeaks in floors are caused by nails used in constructing the floor working loose andrubbing on the floorboard when you step on the area. Because of this the sooner you caneliminate the squeak the better. Young squeaks are much easier to correct than old timers,which have been allowed to grow. |
The JAOAJO Floor Squeak Repair Kit is suitable for all types of wood flooring, carpeted flooring, hardwood flooring, cork/vinyl flooring and linoleum flooring.Mechanical squeaks are caused by the floor rubbing on the cold air return or the floor flex-ing and rubbing on a pipe or electrical line. These are identifiend by a mechanical noisewhen you step on the area. JAOAJO can correct these in many cases by tightening the floorand by eliminating movement in the floor members. |
The JAOAJO Floor Squeak Repair Kit is suitable for all types of wood flooring, carpeted flooring, hardwood flooring, cork/vinyl flooring and linoleum flooring.The JAOAJO system will eliminate most squeaks under carpet,hardwood,vinyland linoleum floors. There can be cases where all squeaks cannot be completelyeliminated. This points to floor damage due to misapplication of the sub floor,water damage,structural damage,mechanical damage and other causes. Thesecases should be referred to a carpenter or floor professional to prevent furtherdamage. |
