Feature

●No need to disassemble: After using this DJI Mini 2 tablet stand, you don’t need to remove it, it can be directly folded on the remote control, and you don’t need to install it again next time. You can use it directly
●Very stable: Ingeniously designed, the tablet bracket is firmly fixed to the rear of the remote control lever with double screws, even a large ipad can be clamped very firmly, without worrying about the risk of the tablet falling
●Comfortable oblique vision: Observing tablet at an oblique angle could prevent reflections under sun
●Anti-scratch & anti-slip: Anti-scratch and anti-slip silicone pad is added to the contact with the plate to protect the plate from scratching
●Wide compatibility: Compatible with almost all 7-12 inch tablet computers on the market (the width of the tablet is between 11cm-19cm), including iPad Mini (7.9"), iPad (9.7"), iPad Air (10.5"), iPad Pro ( 11"), Galaxy Note (10.1"), Galaxy Tab S7 (11"), etc. You don’t even need to take off your tablet case. Note: iPad Pro 12.9" is not supported!
●Applicability: for DJI Mini 4 Pro, Mini 3/ Mini 3 Pro, DJI Mavic 3, DJI Mini 2 SE, Mavic Air 2 and Mavic Air 2S
●Packing list: 1* Tablet Holder 1* screwdriver 1* type C to Type C data cable(11.8") 1* type C to IOS data cable(11.8") 1* remote control lanyard. Note: please connect the Type-C interface with the data transmission logo to the remote control


Description

FPVtosky No Disassembly Tablet Holder for DJI Mini 4 Pro/ Mini 3/ Mini 2 SE/ Mini 2/ Air 3 /Air 2S with Landray and Data Cables

No Disassembly Tablet Holder for DJI MIni 2 /Air 2/Air 2SNo Disassembly Tablet Holder for DJI MIni 2 /Air 2/Air 2S

Compatible with DJI RC-N1/RC-N2 remote control

Compatible with DJI Mini 4 Pro/ Mini 3/Mini 3 Pro/Air 3/Air 2/Air 2S/Mavic 3 drone remote controller

Wide Compatibility(Only Supports Tablets! Tablets are 4.33 - 7.48 inches wide)

Apply to tablets of multiple sizeApply to tablets of multiple size

Compatible with almost all 7-12 inch tablet computers on the market (the width of the tablet is between 4.33“-7.48”), including

  • iPad Mini (7.9in)
  • iPad (9.7inch)
  • iPad Air (10.5inch)
  • iPad Pro ( 11inch)
  • Galaxy Note (10.1inch)
  • Galaxy Tab S7/S8 (11inch)
  • Galaxy Tab A8 (10.5inch)
  • Tripltek 7 Pro (7inch)
  • Tripltek 8/9 Pro (8inch)
  • Others 7-12 inch pad

You don’t even need to take off your tablet case.

Note: Not suitable for 12.9" ipad Pro!! Not supports mobile phones!!

Features of The New Version Upgrade

Compatible with Lanyard ClipsCompatible with Lanyard Clips

Supports thicker tabletsSupports thicker tablets

No More Worrying About Weakened SignalsNo More Worrying About Weakened Signals

Compatible with Lanyard Snap

Solve the problem of not removing the old snap will affect the folding of the tablet, to achieve 100% of the bracket can be folded

Supports Thicker Tablets

Supports tablets up to 16mm thick, perfectly compatible with all Tripltek series and thick tablets with protective cases

No More Worrying About Weakened Signals

Even if the tablet is installed in the RC-N1 / RC-N2 remote control signal area, you no longer need to worry about the signal being affected. Also optimize the tablet bracket structure to make the installation more stable

Tablet Holder Mount Product Features

No disassembly DJI tablet holderNo disassembly DJI tablet holder

Very StableVery Stable

Easy to CarryEasy to Carry

No Disassembly

The first foldable DJI Mini4/3/2 Mavic Air 3/2 tablet holder mount on the market, after installation, it can be directly folded on the remote control, and there is no need to install it next time. Very convenient.

Very Stable

Ingeniously designed, the tablet bracket is firmly fixed to the rear of the remote control lever with double screws, even a large ipad can be clamped very firmly, without worrying about the risk of the tablet falling

Easy to Carry

The tablet holder folded on the remote control can be directly put into the drone bag, which is convenient to carry. Note: Some bags of third-party pre-cut sponges are not supported!

Anti-Scratch & Anti-SlipAnti-Scratch & Anti-Slip

Not Affect Mobile Phone UseNot Affect Mobile Phone Use

Lightweight & StrongLightweight & Strong

Anti-scratch & Anti-slip

Anti-scratch and anti-slip silicone pad is added to the contact with the plate to protect the tablet from scratching

Not Affect Mobile Phone Use

After installing the foldable tablet holder, will not affect the direct use of smart phones, does not affect the recovery of the original phone holder

Lightweight & Strong

The net weight of the tablet stand is 49g (1.73oz), and it is made of sturdy ABS engineering plastic, which is stable and durable without adding too much weight. With the lanyard attached to the product, it is safer and more convenient to use.

DJI Air 2 Tablet Holder Quick InstallationDJI Air 2 Tablet Holder Quick Installation

  1. Insert the black plastic snap in the direction of the arrow in the legend aligned with the remote control;
  2. Connect the plastic snap with the metal hook of the lanyard;
  3. Refer to the illustration of the tablet holder pressed into;
  4. Use the distribution of screwdriver to tighten the bracket on the 2 fixed screws

DJI RC-N1 Controller Tablet Holder Packing ListDJI RC-N1 Controller Tablet Holder Packing List

  • 1 * Tablet holder for DJI Mini 4 Pro/ Mini 3/ Mini 3 Pro/ Mini 2/ Mini 2 SE/ Air 3/ Air 2/2S/ Mavic 3 Classic
  • 1 * Screwdriver
  • 1 * Type-C to Type-C data cables (11.8in) Note: please connect the Type-C interface with the data transmission logo to the remote control
  • 1 * Type-C to IOS data cables (11.8in)
  • 1 * Remote control lanyard


From the brand

Product guides and documents

Looking for specific info?

Product information