Feature

●Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass.
●Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer
●Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable
●Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filters frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s)
●High Level Input - Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB8 to your factory radio or an aftermarket radio that does not have low-level (RCA) inputs
●Low Level Input - Line level inputs, also known as RCA inputs or low-level inputs, use RCA interconnect cables to link the BAB8 with the source unit. Most aftermarket radios have multiple pairs of RCA outputs that can connect to multiple amplifiers
●Variable Bass Boost - Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it


Description

imageimage
imageimage

imageimage
Subwoofers

Amplified Car Subwoofer - 800 Watts Max Power, Low Profile, 8 Inch Subwoofer, Remote Subwoofer Control

BAB8

Break Your Subwoofer In. Much like the engine of a new automobile, a new subwoofer must go through a short but important process of “break-in” before it is run under harsh conditions. The “break-in” process will ensure the subwoofer is able to perform as it has been designed to. This process involves subjecting the subwoofer to no more than low-to-medium volume levels for a number of hours in the enclosure. 3-4 hours is generally sufficient for the subwoofer’s suspension to loosen enough to prevent the voice coil(s) from overheating and causing failure. The break-in period is also effective in extending subwoofer life. Over-driving the woofer before it has been properly broken-in will usually result in premature failure and poor performance.

  • • One 8" Woofer with SINGLE 2.6 ohm Voice Coil
  • • 800 Watts MAX 400 Watts RMS Power Handling
  • • RCA & Speaker Level Inputs, High Level Inputs
  • • Thermal, Short and Overload Protection Circuits, Power & Protection LEDs
  • • Phase Control, Subsonic Filter, Low Pass Crossover, Variable Bass Boost, Input Gain Control

Features

testtest

imageimage

imageimage

imageimage

IPX5 Rating

The IPX5 Rating means that the equipment will be protected against low pressure water stream from any angle.

Class A/B

Our Class-A/B amplifiers feature specific linear circuitry that increases sound quality and power output while reducing distortion and improving efficiency.

Mosfet Power Supply

Metal Oxide Semiconductor Field-Effect Transistors quickly switch from full to non-conduction for high efficiency output.

High & Low Level Inputs

High-level inputs accept speaker output signals and low-level inputs accept pre-amp output signals to allow for the addition of amps and processors to standard factory or aftermarket source units.

imageimage

imageimage

imageimage

imageimage

Phase Control

This function on the amplifier comes in handy for custom installations where you might need to have your speakers or subwoofers mounted the non-traditional way with the magnet facing out. Let us explain. You can set the Phase anywhere from 0 degrees to 180 degrees. What this does is that it reverses the polarity (Positive/Negative) on your subwoofer terminals which in turn reverse the direction of the low frequency BOOM that you are used to hearing.

Variable Bass Boost

Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Variable Low Pass Filter

Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

Remote Sub Control

A wired remote lets you easily control the subwoofer level for customized output and superior sound.