Feature(may vary by option.)

●♞【Product】3 Axis nema23 stepper motor driver controller kit; Model Number:23HS8430B/TB6560
●♞【Stepper Motor Driver】 : MD430 Stepper Motor Driver 3Amps / Support voltages:12-34VDC / Step frequency up to 100khz / 2 phases bipolar driver
●♞【Nema 23 Stepper Motor】 Nema 23 Stepper Motor / Holding Torque: 270 oz-in,180N.cm / Motor Size:57x57x76mm / Phase:2 / Motor wire:4pcs / 1.8 Step
●♞【5 Axis Breakout Board】 Come with DB25 parallel cable and USB cable;Support MACH3,KCAM4,EMC2 and other software;5-way input interface, you can connect limit switch and stop switch,reset,knife signal;

[3 Axis-D]




[4 Axis-D]





Description

Package include:

  • 3 x TB6560 MD430 single axis driver
  • 3 x 23HS8430B Nema23 stepper motor 76mm 270oz-in Dual Shaft
  • 1 x 350W 24V DC switching power supply
  • 1 x 5 axis breakout board
  • 1 x DB25 LPT parallel cable
  • 1 x USB cable
  • English user manual for breakout board and stepper motor driver will send by message.

23HS8430B Nema23 Stepper Motor

22

Wirings:

4 Wires
  • Stepper motors red wire connect to drivers A+ port
  • Stepper motors green wire connect to drivers A- port
  • Stepper motors yellow wire connect to drivers B+ port
  • Stepper motors blue wire connect to drivers B- port
General Specification:

  • Step angle accuracy:+ - 5%(full step,not load)
  • Resistance accuracy: + - 10%
  • Inductance accuracy:+ - 20%
  • Temperature rise: 80deg Max(rated current,2 phase on)
  • Ambient temperature: 20deg-50deg
  • Insulation resistance:100ohm Min,500VDC

Electrical Specification:

* Model Number: 23HS8430B

* Motor Type: Hybrid

* Step Angle: 1.8 deg

* Holding Torque: 1.8Nm (270oz.in)

* Rated Current/phase: 3A

* Body Length: 57x57x76mm

* Number of Leads: 4

* Weight: 1.1kg

front shaft is 8mm diameter shaft,21mm lenth

back shaft is 6.35mm dia and 10mm length

MD430 stepper motor driver

11

22

22

  • 1) Single-chip motor driver for sinusoidal microstep control of stepping motors
  • 2) Power on in indication led
  • 3) 3Amps,34Volts (Supply voltages: 12-34VDC)
  • 4) Full step, half step, eight step and sixteenth step(selection with dipswitches)

  • 5) Torque (100%, 75%,50%, 20%)
  • 6) Work Current (0-3A selection with SW1/SW2/SW3)
  • 7) 4 Wire,6 Wire,8 Wire stepper motors can be used
  • 8) Two phases bipolar driver
  • 9) Easy wiring with standard screw terminals
  • 10) Step frequency up to 100khz

  • Stepper motors red wire connect to drivers A+ port
  • Stepper motors green wire connect to drivers A- port
  • Stepper motors yellow wire connect to drivers B+ port
  • Stepper motors blue wire connect to drivers B- port

5 axis breakout board with DB25 parallel cable and USB cable

11

33

22

Description:

  • Support MACH3,KCAM4,EMC2 and other software;
  • Control five stepper motor driver;
  • 5-way input interface, you can connect limit switch and stop switch,reset,knife signal;
  • Input signal then have LED indicates;
  • NO and NC port of relay all allow，you can choose them to control spindle;
  • Can choose USB of PC to supply 5V or external power supply 5V;
  • Data transfer speed can up to 10MBit/s;
  • Output pin with extension interface.

25-pin parallel port control

  • This breakout board needs to be connected to the parallel port and USB port of the computer at the same time.
  • The USB port on the board is only used to provide 5V input.

Can support limit switch

  • The interface board uses a high-performance three-state bus driver
  • 74HC244 and schmitt inverter 74HC14,
  • The signal drive capability is stronger and more stable after filtering. add 5V input terminal and the light of input and relay,makes the operation more convenient to use.
2222

DB25 Pin

  • 1 EN=Enable all axis
  • 2 STEPX=X pulse signal
  • 3 DIRX=X direction signal
  • 4 STEPY=Y pulse signal
  • 5 DIRY=Y direction signal
  • 6 STEPZ=Z pulse signal
  • 7 DIRZ=Z direction signal
  • 8 STEPA=A pulse signal
  • 9 DIRA=A direction signal
  • 10-13 LIMIT-1/2/3/4=input1/2/3/4
  • 14 RLY=Relay
  • 15 LIMIT-5=input5
  • 16 STEPB=B pulse signal
  • 17 DIRB=B direction signal
  • 18-25=GND

350W 24V DC Switching power supply

44

55

66

Specification

  • Model: S-350W-24V
  • Output Current:14.6A
  • Output Voltage:36V
  • Output Frequency:85%
  • Output Power: 350W
  • It comes with built-in cooling fan

Connection instruction

  • L: Live wire
  • N: Negative wire
  • +V: DC power output “+”
  • -V: DC power output “-“
  • +V ADJ: output voltage regulation

110V or 220V

  • Input: 110-120V AC or 220V-240V AC
  • Please flip the side input voltage selector switch
33