Feature
●【Sensitive Control】The electric bicycle controller is a brushless motor controller, which can provide stable speed and sensitive control of braking and direction changes.
●【Professional Design】: Exquisite workmanship, beautifully painted and has a bright appearance, numerical controlled precision bending. durable.
●【Circuit Protection】The case is made of thickened aluminum alloy.its good heat dissipation function, it can protect the internal circuit and avoid thermal overload.
●【Wide Application】:Suitable Motor Phrase Angle: Auto recognition. It can drive sine wave motors, suitable for hall sensored brushless DC motor ., can support 36-48-60-72-84V, Suitable for: electric bicycle, scooter,Small tricycle,Two-wheeler etc.
●【High quality service】: Each cable has an instruction label, which is very detailed and easy to install.If you have any product issues, please dont hesitate to contact us via Amazon message system, we will do our best to solve for you.
Description
JRAHK Electric Bicycle Sine Controller
E-bike BLDC Controller Three-mode controller
What is a Three-mode controller?
- Quiet start(Except for special circumstances)
- strong power and power saving.
- The three-mode controller is a sine wave controller.
- It can operate in three modes, sine wave mode, square wave mode, and no hall mode (that is, it can be used without a hall sensor).
- The mode cannot be selected, the default is sine wave mode.
- When the hall sensor is damaged it will automatically switch to square wave mode.
- Runs no-Hall mode when no Hall sensors are connected.
- Suitable for in-wheel motors.Differential motor, etc.
Tips:
- Applicable to a variety of motors, but only in-wheel motors with Hall sensors can use sine wave mode.
- When running other motors, it will automatically switch to square wave mode or no Hall mode.
Line specification
- 1. Power supply，2.Motor phase line
- 3.Anti-theft signal，4.Anti-theft power supply
- 5.Intelligent learning，6.Throttle
- 7.High level brake
- 8.Key switch
- 9. Dial gear three speed
- 10. Phase line speed measurement
- 11.One line pass
- 12. Differential motor special
- 13. Fixed speed cruise control
- 14.PAS
- 15.Low level brake
- 16.Reversing
- 17.Hall sensor
- 18.Hall speed measurement
|
|
|
|
|---|---|---|
Route indicationEach Line is marked in Engilsh |
Installation referenceRefer to some line installation instructions |
Line function installationStep 1. Connect wires 1, 2, 6, 8, 17. Step 2. Connect the No. 5 wire with the motor suspended. (Note: the motor needs to be in the overhang position for docking wire #5) Step 3. The motor will perform a forward/reverse state. (If there is a reversal you will need to disconnect the 5 wire and reconnect it) Wait 10 seconds in the forward state to complete learning. Step 4. Make the wiring connections according to the vehicle. |
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|
| 2000W sine wave controller | 2000W Square wave controller | 3000W square wave controller | 2500W sine wave controller | 866 2000W sine Wave Controller kit | 866 400W sine Wave Controller kit | |
| Color | Gold | Blue | Blue | Orange | Red | Red |
| Type | Sine wave | Square wave | Square wave | Sine wave | Sine wave | Sine wave |
| Current limit | 34A-40A | 34A-40A | 45-60A | 45-50A | 34A-40A | 7A-20A |
| Voltage | 36V-48V-60V-64V-72V -84V | 36V-48V-60V-64V-72V -84V | 48V-60V-64V-72V -84V | 36V-48V-60V-64V-72V -84V | 36V-48V-60V | 36V-48V-60V |