Feature(may vary by option.)

●【Motor and TB6600 Driver wiring】Stepper motors RED wire connects to drivers A+ port. Stepper motors GREEN wire connects to drivers A- port. Stepper motors YELLOW wire connects to drivers B+ port. Stepper motors BLUE wire connects to drivers B- port.
●【Control Card and TB6600 Driver wiring (X-axis as an example) 】Drivers "CLK-" connects to control cards XP pin , Drivers "CW-" connects to control cards XD pin , Drivers "5V" connects to control cards 5V pin.(The USB Mach3 control card cant support connection EN- and EN+).
●【Low Noise/High Torque Hybrid Stepper Motor】23HS8430B 2-phase stepper motor with dual shaft diameter of 8mm, a current of 3A and an angle of 1.8°, is made of durable metal on the outside, and the perfect combination of rubber and rotor fills up the inner space and stabilizes the overall structure of the motor. The coils are made of pure copper enameled wire and the torque is up to 270oz-in (180N.cm/18kg-cm). The motor runs quietly and doesnt cause the generator to become too hot over a long time.
●【Upgraded 4.5A Stepper Motor Driver】Using the latest TB6600 new installation chip, there are low-voltage shutdown, thermal over-stop and over-current circuit protection, and compared with the TB6560 increased short-circuit protection. TB6600 driver operating voltage of DC 10-45VDC, support for sub-division of the whole step, half-step, 1/4, 1/8, 1/16 step, up to 42/57/86 two-phase / four-phase / four-wire / six-wire stepper motors within 4.2A. / six-wire stepper motor.
●【USB Interface, Drive-free Design 4-Axis Linkage Control Card】Output pulse frequency of 100KHz, using the minimum error interpolation algorithm, high processing accuracy. Supports up to 4 axes of linkage control, of which the 4th axis can be set as the slave axis. The control card can be connected to PC-compatible computers such as laptops, desktops, tablets and other computers with a USB interface. As long as Mach3 is running, the control card can be used without installing any drivers.
●【Multi-function control card】General-purpose opto-couplers isolation input : can support the limit switch, emergency stop switch, auto tool zero, home switch and electronic handwheel; Have 0-10V signal output , you can use mach3 software to control the spindle motor speed; 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps or other device.
●【Stable output 24V DC power supply】Over-current, over-voltage and overload protection, power supply stable power supply, electrical energy conversion rate of up to 90%, higher efficiency. Together with the heat dissipation fan design, shell hollow design, heat dissipation ability faster and stronger, more durable performance.

[3 Axis-A]




[3 Axis-B]




[4 Axis-B]




[4 Axis-A]




[3 Axis-C]




[4 Axis-D]





Description

4 axis nema23 270oz-in 76mm stepper motor dual shaft+md430 tb6560 driver cnc kit4 axis nema23 270oz-in 76mm stepper motor dual shaft+md430 tb6560 driver cnc kit

Package Include

  • 4 × Nema23 Stepper Motor 57mm
  • 4 × TB6600 Stepper Motor Driver
  • 1 × Mach3 USB CNC Control Card+USB Cable
  • 1 × DC Switching Power Supply

cnc controller kit nema 23cnc controller kit nema 23

cnc router stepper motor and controller kitcnc router stepper motor and controller kit

cnc driver controller kit plasma cuttercnc driver controller kit plasma cutter

Nema23 Stepper Motor Double Shaft/270Oz-in/2 phase

Motor Type: Hybrid Stepper

Step Angle: 1.8 degree±5%

Voltage: 4.8V

Holding Torque: 180N.cm(270oz-in)

Detent Torque: 6N.cm Max

Rotor inertia: 440g.cm²

Phase Resistance: 1ohms

Insultaion Class: B

Inductance: 3.5mH+/-20%(1KHz)

Front shaft is 8mm diameter shaft,21mm lenth,back shaft is 6.35mm dia and 10mm length

TB6600 Stepper Motor Driver 4.5A

  • The working voltage is DC 10V-45V.
  • Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.
  • Using Toshibas new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.
  • The rated maximum output reaches: ±4.5A. Automatic half-flow function.
  • Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.
  • Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.

USB Mach3 Motion Control Card Introduction

  • The motion control card for machine control, with strong professional.Requires the operator to have the relevant expertise!If used improperly, may appear an accident, please strictly follow the instructions and warnings using this product if you are not sure, consulting engineers for help.
  • First time users, if you are not familiar with the product and software features Mach3 In your test product, make sure the machines power switch on hand, you can quickly turn off the power.

cnc 4 axis kitcnc 4 axis kit

cnc motor and driver kitcnc motor and driver kit

stepper motor bracketstepper motor bracket

350W 24V DC Switching Power Supply

  • DC output: 24V 0-14.5A
  • Inlet stability: ±0.5%
  • Load stability: ±0.5%
  • DC voltage of Adjustable range: ±10%
  • AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switch
  • Overload protection: 105%-135% cut off the output, automatic recovery
  • Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover
  • Setup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full load
  • Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute
  • Isolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ

How to connect the Tb6600 driver ( or Stepper Motor) to CNC Motion Control Card?

  • It should be noted that the wiring diagram of the 4-axis motion control card above is for reference only, then if you connect this control card and the TB6600 driver, such as connect to X-axis motor driver, then:

  1. Drivers "CLK-" connects to control cards XP pin ,
  2. Drivers "CW-" connects to control cards XD pin ,
  3. Drivers "5V" connects to control cards 5V pin.(The USB Mach3 control card cant support connection EN- and EN+ ).

  • Stepper motors wrings ( 4 wires) :

  1. Connect stepper motors RED wire to drivers A+ port
  2. Connect stepper motors GREEN wire to drivers A- port
  3. Connect stepper motors YELLOW wire to drivers B+ port
  4. Connect stepper motors BLUE wire to drivers B- port

Bracket for Nema 23 Stepper Motor

  • The holder is made of alloy steel, is strong and durable and cannot be easily deformed.
  • With this holder, the stepper motor Nema23 can be firmly attached.
  • All slots and openings of the holder have been finely stamped to ensure accurate dimensions, and can be used perfectly with the motor.
cnc stepper motor kit nema 23 win 10cnc stepper motor kit nema 23 win 10

Description of TB6600 Stepper Motor Driver

  • There are two input terminals, both of which adopt the common anode input mode.
  • The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.
  • The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.
  • The motor rotates forward when CW is high or suspended, and reverses when it is low.
  • When EN is high or floating, it is working state, when it is low, it is offline.
  • Note 1: The power supply cannot be connected reversely, otherwise the chip will be burnt out.
  • Note 2:The set current should not exceed the rated current of the motor.

4 Axis CNC USB Mach3 Controller Breakout Board

mach3 usb cnc controller boardmach3 usb cnc controller board

4 axis stepper motor driver4 axis stepper motor driver

tb6600 stepper motor drivertb6600 stepper motor driver

  • Support for 4-axis linkage, you can connect four stepper motor drives or servo drives;
  • Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;
  • 4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop switch, auto tool zero, home switch etc.
  • Support for connecting electronic handwheel.

  • Have 0-10V signal output , you can use mach3 software to control the spindle motor speed.
  • 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps or other device.
  • 1 status LED, indicate connection status on the board.

  • This USB motion card does not need install any USB driver, It can be identified directly.
  • Windows2000/XP/Windows7,can directly identify (Notice: Doesnt support Win8/win10/macOS system !!!) .
  • It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.
usb cnc controllerusb cnc controller

350W 24V DC Switching Power Supply

nema23 stepper motot kit 3 axisnema23 stepper motot kit 3 axis

350W 24V power350W 24V power

mach3 controllermach3 controller

Multiple protection, Stable Performance

  • Short circuit protection: when the output terminal is short-circuited, the power supply turns off the output, and the output voltage is 0V.
  • Overcurrent protection: When the output current>115-150%, the output voltage turns off the output.
  • Overload Protection: Power protection when load power＞105-135% of rated power.
  • Temperature protection; the power supply is automatically protected at high temperatures.

Double Ball Cooling Fan and Full Metal Housing Design

  • With high speed and quite characteristics, it can ensure the temperature operation of the equipment and extend the service.
  • The shell is made of aluminum alloy with high thermal conductivity system, which is reinforced and durable, and the design is more user-friendly.

Input Voltage Switch

  • The power supply has an input voltage 110V-220V switch button, which can adapt to different voltage requirement.
  • Quadruple protection setting, high resistant to electricity, effectively reducing the impact of AC input.