A: Removal Adapter (1.148" L x 1/2" I.D. x 3" O.D.)
B: Screw
C: Installing Cup (3.676" L x 1-3/4" I.D. x 2" O.D.)
D: Installation Adapter (1.122" L x 0.941" I.D. x 3" O.D.)
E: Forcing-screw Press (Inner Length: 6.22"/158mm)
F: Receiving Cup (2-1/2" L x 2" I.D. x 2-1/4" O.D.)
G: Receiving Tube (1-3/4" L x 1-3/4" I.D. x 2" O.D.)
H: Receiving Tube (1-3/4" L x 2-1/4" I.D. x 2-1/2" O.D.)
I: Receiving Tube (2-1/4" L x 2.723" I.D. x 3" O.D.)
J: Install Cup Adapter (0.845" L x 1.879" I.D. x 2-1/4" O.D.)
1. Assemble the Ball Joint Press (1) over the vehicles control arm. Select the correct size Receiving Tube (3,4,or 5), and position it under the vehicles ball joint.
2. Place the Removal Adapter (7) between the Receiving Tube and the Jackscrew (2).
3. Then, place the Installation Adapter (6) between the top of the ball joint and the Ball Joint Press.
4. Tifhten the Jackscrew until the Receiving Tube contacts the vehicles control arm.
5. Check the alignment of all the Ball Joint Kit parts, and continue tightening the Jackcrew until the vehicles ball joint is removed.
1. Clean the vehicles control arm, and coat the inside diameter of the control arm with a light lubricant.
2. Insert the replacement ball joint as straight as possible into the vehicles control arm.
3. Assemble the Ball Joint Press over the vehicles control arm. Select the correct size Receiving Tube and position it on top of the vehicles control arm.
4. Place the Installation Adapter between the Receiving Tube and the Ball Joint Press. Then, place the Removal Adapter between the ball joint and the Jackscrew.
5. Check the alignment of all the Ball Joint Kit parts. Then, tighten the Jackscrew until the vehicles ball joint is firmly sealed.
1. To remove the brake anchor pins, remove all lock ring retainers from the Brake Anchor Pins.
2. Position the Ball Joint Press over the brake spider.
3. Tighten the Jackscrew until the anchor pins can be removed.
4. To install the brakke anchor pins, insert the brake anchor pins. Then reinstall the lock ring retainers on the brake anchor pin.
5. Unscrew and remove the Ball Joint Press.
1. To disassemble a U joint, remove any external and/or internal lock rings.
2. Position the Ball Joint Press around the drive shaft yoke and tighten the jackscrew until the first bearing is removed. Reposition the ball joint press and remove the second bearing.
3. To assemble a U joint, clean all dirt and oil from the yoke area. Align the replacement bearing and Ball Joint Press as straight as possible over the yoke. Press the replacement bearing into the yoke, and reassemble the external/internal lock ring.
4. Reposition the ball joint press and second eplacement beaing as straight as possible over the yoke, and press the beaing into the yoke.
5.Reassemble the external/internal lock ring.
To Remove a Ball Joint
To Install a Ball Joint
To Remove and Install Brake Anchor Pins
To Disassemble/Assemble a U Joint
|
|
|
---|---|---|
Quality SetThis DAYUAN tool set is made of ultra carbon steel, these components will stand up to heavy use and accidental drops. Its even for professional mechanics. |
Wide VarietyThis tool set fit most American domestic and imported 2-wheel drive (2WD) and 4-wheel drive (4WD) cars and light pickup trucks that have press-fit type ball joints |
East StorageComes in a blow molded case for safe & easy transport and storage. |