[A-1]
.Lacquer free dent repair kit: It is a lacquerless dent removal tool designed based on the lever principle. The dent extractor can remove strong adhesive dents, and the hot melt can be completely removed without damaging the paint. Kind reminder: It is recommended to use cars with original paint. If your paint is damaged before repairing dents, we do not recommend using a repair kit, otherwise the adhesive will stick off the repair paint and the dents will not be removed.
Easy to use tools: The dent puller kit is suitable for beginners and professionals. The design of the dent repair tool is simple. Most dents can be eliminated within 30 minutes. The dent removal kit comes with a repair introduction. It can act on dents on the surface of cars, motorcycles, and other metals. Dont hesitate.
|
|
|
---|---|---|
2 In 1 T-bar Puller(long and short type)The two in one T-shaped rod is made of iron and is suitable for large dents. You can use a hot melt gun to assist and then use a blue plastic sheet for repair. In addition, it can also be decomposed into a small T-shaped steel bar. Meet different needs. |
Dent Puller KitDent Puller Kit Composed of plastic and aluminum materials, suitable for dents with a width of less than 2.36 in. You can use a hot melt gun for assistance, and then use a blue plastic sheet for operation. |
Bridge Dent PullerThe bridge type dent puller is composed of plastic and aluminum materials and is suitable for dents with a width of 1.18 to 3.14 inches. You can use a hot melt gun for assistance, and then use a blue plastic sheet for operation. |
|
|
|
---|---|---|
Metal tapping pen and Rubber HammerA hammer is used in conjunction with a striking rod to gently strike protruding points |
inch indentation pullerFor the repair of large depressions using vacuum suction cups, it is necessary to clean the large depressions with a towel before operation |
Hot melt adhesive gun (100W) and hot melt adhesive rodCome with a 100W hot melt glue gun and 10 hot melt glue sticks. There is no need to purchase another part, enough for most dent can meet. |
--2* Stainless Steel Grooves
--2* Short Puller Lines+2* Long Puller Lines
--64* Glue Tabs
--1* Rubber Hammer
--1* Empty Bottle
--2* Yellow Plastic Shovels
--1* Pair of White-Glove
--1* Rag
--1* Product Instruction
--1 * 2-in-1 T-shaped rod puller (long and short)
--1 * Bridge Dent Puller and 7 * Accessories
--1 * Gold tooth elevator
--1 * 4.72 inch indentation puller+2 * 2.36 inch indentation puller
--1 * Metal tapping pen (with 9 pen tips)
--1 * Dent Puller Kit
--1 * Hot melt adhesive gun (100W)+12 * Professional hot melt adhesive rod
How to remove large dents?
1. Clean the dents and ensure that the car paint is intact and undamaged.
2. Insert the glue stick into the 100W glue gun and heat it for about 5-7 minutes until the glue overflows from the gun.
3. Select a label and apply hot melt adhesive to it.
4. Place the label on the dent, grab it and wait for 3 minutes until the hot melt adhesive turns into a block.
5. Use a T-bar dent extractor to extract the dent. Repeat the above steps until the dent pops out.
6. Spray 75% alcohol onto the remaining glue. Wait for 3 minutes.
7. Shovel it off or use a plastic spatula to scoop it out.
How to use a bridge type dent puller?
1. Insert the hot melt adhesive rod into the 100W adhesive gun, and then heat it for about 5-7 minutes until the adhesive overflows from the gun.
2. Select a suitable plastic adhesive pad and apply hot melt adhesive to it. The bridge dent puller has 7 black protrusions that you can choose based on the size of the dent.
3. Place the plastic adhesive pad on the dent, grasp and wait for three minutes until the hot melt adhesive turns into a block.
4. Use a bridging dent puller to align, then slowly tighten the screw with appropriate force until the dent surface becomes flat or visibly protruding. This process should be carried out cautiously and slowly.
5. Spray 75% alcohol onto the remaining glue and wait for 3 minutes. Peel it off or use a plastic yellow spatula to remove it.
How to use a gold tooth elevator?
1. Insert the glue stick into the 100W glue gun, and then heat it for about 5-7 minutes until the glue overflows from the gun.
2. Select a suitable plastic adhesive pad and apply hot melt adhesive. 64 plastic adhesive pads can be used.
3. Quickly place the plastic adhesive pad on the dent, grab it and wait for three minutes until the hot melt adhesive turns into a block.
4. Use a dent elevator and adjust its height to repair the dent.