Feature
●Open a 2" dimension and 2-3/4" depth hole, put gauge into it and fasten
●Indicating Range: 0-9990RPM, Speed Ratio: 1-300 adjustable, You can press the back button to adjust it. Idle speed is typically 600-800rpm. Details refer to owner manual.
●Suitable for diesel engine and gasoline engine. Tachometer can get signal from engine, ignition coil, crankshaft sensor, or tacho sensor (be sold separately), etc..If you need tacho sensor, pls. search for ASIN NO. B07RN3HJ72 or B07RR8NQ45
●It shows rpm and hour. Hourmeter cannot be reset. If you need other faceplate , pls. search for ASIN B0755JF9FK or B0755FJHBP
●Red Backlight, 9-32VDC(12VDC/24VDC) Working Voltage,1 year Warranty, 100% Waterproof and anti-fogging protection
Description
Product Features:
-Be suitable for all kinds of tacho RPM sensors, and display the rotation speed of the engine.
-Use moving-magnet principle to drive the needle, featuring good endurance and anti-vibration.
-IP67 waterproof and dustproof grade
-Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc.
-With curved glass (with anti-fogging function)
-With ultra-wide working voltage design( long-term operating voltage: 9-32V, Maximum up to: 36V (≤ 1 min)).
Product Introduction
|
|
|
|
|---|---|---|
How to install it ?- Cut an 52mm (2 1/16") hole in the panel and allow a clearance of 70mm (2 3/4”) behind the panel to fit the gauge. - Put the gauge in the hole. - Using M4 nut and C type bracket to seal up the gauge. |
How to connect wires ?Red wire --- Power Positive. Black wire --- RPM Signal. Orange wire (backlight) --- Power Positive. Blue wire --- Power Negative. Please note: Digital tachometer can be connected to 12VDC and 24VDC power directly. |
Why Dont get RPM signal ?Digital tachometer sometimes cannot get signal by ignition system. So, I suggest Tacho sensor signal. It is more stable. I suggest you can buy a Tacho sensor from Eling Parts. NO. is B07RR8NQ45, B07RN3HJ72. |
How to be setting Tach RPM Ratio?
1. Turn on the power supply first.
2. Press and hold the mode button for 3 seconds to enter the setting speed ratio mode. then adjust speed ratio from 1-300 according to your request.
3. After setting, Data is automatically saved.
4. Please note: If your sensor is installed on the flying wheel panel, the RPM ratio is equal to the number of gears of the engine; If the speed signal takes from W-Terminal, the RPM ratio is equal to the half of the number of poles.
5. Normally, When the engine at idle state, tachometer shows 600-800rpm that means speed ratio is correct. If not, you can turn down or turn up speed ratio to check RPM difference.
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|
| Tachometer | Tachometer | Tachometer | Tachometer | Tachometer with oil pressure water temp voltmeter | Tachometer with oil pressure water temp fuel level voltmeter | |
| Customer Reviews |
— |
61
|
85
|
— |
— |
3
|
| Price | $41.99 | $45.99 | $36.99 | $34.99 | $51.99 | $52.99 |
| size | 85mm | 85mm | 85mm | 85mm | 85mm | 85mm |
| color | white+stainless steel | black+stainless steel | black+black | white+stainless steel | black+stainless steel | black+black |
Package Includes:
1x Digital Tachometer
1x Multi-plug socket
1x Installation Instruction